GrowLED

Master Products at GrowLED: choosing harvest machinery and accessories

The GrowLED team 4 min read

Master Products at GrowLED: choosing harvest machinery and accessories

GrowLED is an official Master Products retailer in France and Europe. Start with the job you need to do. Removing flowers from stems, trimming leaves, grading flowers and drying a batch each require different equipment. The following examples show how to specify a system your team can operate and maintain.

Follow a batch through the workshop

Example for dry trimming. If flowers arrive separated and dried, start at the MT Dry.

MB Bucker 200

1. MB Bucker 200

Whole branches → separated flowers. Plan a container for each outlet.

MT Dry 200

2. MT Dry 200

After drying → trimmed flowers. “Dry” describes the incoming material. Drying takes place upstream.

MS Sorter 100 LiTE

3. MS Sorter 100 LiTE

Trimmed batch → size grades. The trays sort flowers by size before packing.

From whole branches to graded flowers

When branches arrive intact, an MB Bucker can separate the flowers from the stems before trimming. For a quotation, record the typical stem diameter, the daily batch weight and the number of operators feeding the machine. Compare fresh throughput figures with other figures measured on fresh material.

After trimming, MS Sorter equipment grades flowers by size. The MS Sorter 100 LiTE uses stacked trays for manual grading on a workbench. The MS Sorter 500 fits into a line with space for collection bins. For seed production, the MS Seeds range performs a different job, separating seeds from plant material.

MS Sorter 100 LiTE
MS Sorter 100 LiTE · Master Products

MT Dry 200: specifying the machine and drum

The MT Dry 200 trims dried flowers. Master Products specifies a 90 W motor, a 250 mm cutting drum and throughput of up to 3.5 kg/h. Allow time for loading, unloading and cleaning between batches when estimating daily capacity.

The 120 µm hexagonal pollen drum is sold separately. It uses the lid from the machine. Sets of six screens allow operators to replace its panels or change mesh size. A set of screens requires a pollen drum to fit them to. Check the machine plate first as the Dry 100 LiTE and the Dry 200 LiTE each have their own accessory.

MT Dry 200 · 120 µm
MT Dry 200 · 120 µm · Master Products

Compatibility diagram · from trimming to mesh panels

Three items serve different purposes on the MT Dry 200. Read the full model name before ordering.

MT Dry 200

1. MT Dry 200

Use the machine’s trimming drum for dry flowers.

Pollen drum

2. Pollen drum

For sieving, order the hexagonal drum separately. The 120 µm version uses the existing lid.

Six mesh panels

3. Six mesh panels

To replace the sieving surfaces, choose the panels for the pollen drum already installed.

MT Tumbler 500: include leaf collection in the quotation

Removing leaves from the trimming station matters as much as feeding it. The MT Tumbler 500 requires a vacuum purchased separately. The two options offered are the Standard Leaf Collector and the Trim Filter. Drum choice also depends on whether the harvest is wet or dry.

Mark the operator, feed point, flower collection area and vacuum emptying position on the layout. This makes it easier to decide whether an infeed or outfeed conveyor will help. For a replacement filter or brush, a photo of the machine plate and the existing assembly helps identify the right part.

MT Tumbler 500
MT Tumbler 500 · Master Products

Extraction, inspection and freeze-drying

MX Ice equipment uses ice water. Plan for the water supply, drainage and access for cleaning the vessel. Plasmastatic equipment separates dry fractions electrostatically. Size each workstation for the material it will receive.

Lio 40 and Lio 70 freeze dryers dry material by sublimation under vacuum. Both sizes offer a standard pump or an oil-free pump. Each variant price includes the pump selected. Check access to the room, door clearance and pump maintenance requirements when choosing a model.

MX Ice 200 LiTE
MX Ice 200 LiTE · Master Products

Size a line around the working day

Example: 12 kg of dry flowers in six hours, with two hours for setup, changeovers and cleaning, leaves four operating hours. The target is 3 kg/h. Against the Dry 200 maximum of 3.5 kg/h, the theoretical headroom is 0.5 kg/h. Test a representative batch to see whether this is sufficient.

Time the next station too. If grading and collection take 2 kg/h while trimming produces 3 kg/h, one kilogram queues every hour. Assess the trays, bins and staffing before increasing trimming capacity.

Four specialist stations: which one fits your batch?

Each station has a different purpose. Start with the output you need.

MS Seeds 200 / 500

MS Seeds 200 / 500

Separate seeds from plant material. Choose MS Sorter when the required output is size-graded flowers.

MX Ice

MX Ice

Ice-water separation. Locate water and drainage points before positioning the vessel.

Plasmastatic

Plasmastatic

Electrostatic separation of dry fractions. Specify feed material and volume when comparing Pilot, V1 and V2.

Lio 40 / 70

Lio 40 / 70

Freeze-drying. Size this station by batch and cycle. Include the pump choice in your enquiry.

Request a workshop quotation

Email [email protected] with the model, incoming material, target throughput and delivery location. For a spare part, include a photo of the machine plate. Your quotation can then identify the machine, separately purchased accessories and freight.

Instalment payment depends on order value, options displayed at checkout and approval. Check the lead time on each offer, including special-order equipment.

Cet article t'a été utile ? Le parcours de la GrowLED Academy reprend tout dans l'ordre où on monte une culture, de la box à la récolte. Gratuit, sans compte.
Voir les 10 étapes