CannaLED Spider Series: The Modular LED Lighting Revolutionizing Indoor Cultivation
The CannaLED Spider Series represents a new generation of modular LED lighting specifically designed for indoor cultivation. With its interchangeable LED bars and adjustable UV/IR spectra, this range offers unparalleled flexibility to adapt lighting to different growth phases. Each model in the Spider Series integrates Samsung LM301B diodes and dedicated UV/IR chips to maximize yield and crop quality.
Why choose the CannaLED Spider Series for your setup
The modular system of the Spider Series is a real game-changer. Unlike traditional LED panels, you can adjust the bar configuration according to your needs: bring the bars closer for intensive coverage over a small area or space them out to cover a larger area. Samsung LM301B diodes deliver a homogeneous PPFD of 800 to 1200 µmol/m²/s depending on the model, while the UV (365nm) and IR (730nm) channels can be adjusted independently via the integrated controller.
Energy efficiency reaches 2.9 µmol/J on PRO models, which is 30% more than a standard LED panel. Passive heat dissipation avoids noisy fans – a real plus for discreet setups. The bars connect in a daisy-chain with a single power cable, which greatly simplifies installation in a grow tent.
How to choose your Spider Series model
For an 80x80cm tent, the Spider 240W is more than sufficient with its 4 x 60cm bars. 100x100cm tents typically require the Spider 320W or 480W depending on the desired intensity. The Spider PRO Series adds separate spectrum control – essential if you want to boost UV at the end of flowering or use IR to emulate sunset.
Check the available height carefully: allow a minimum of 40cm between the ceiling and the bars for ventilation. 600W and larger models generate more heat and require more powerful extraction. The 0-100% dimmer allows you to adapt the power according to the phase: 40% for germination, 70% for vegetative growth, 100% for flowering.
Frequently Asked Questions
What size Spider Series should I choose for my 100x100 cm tent?
For a 100x100cm tent, the Spider 320W represents the viable minimum with a PPFD of 600-700 µmol/m²/s. The Spider 480W offers more headroom with 800-900 µmol/m²/s, ideal for boosting yields. The Spider 600W PRO is suitable for experienced growers who master environmental parameters, as it delivers over 1000 µmol/m²/s. Count approximately 30-35W per square foot as a general rule.
How do I adjust the UV/IR spectra on the Spider PRO Series for the flowering phase?
During flowering, gradually activate UV from the 3rd week: start at 20% then increase to a maximum of 50% for the last 2 weeks. UV stimulates trichome production but can stress plants if improperly dosed. For IR, use it 15 minutes after the main light turns off to simulate sunset – this accelerates the transition to the night phase. The controller allows you to program these cycles automatically.
Is the Spider Series more efficient than classic LED panels like Mars Hydro for indoor cultivation?
Yes, the Spider Series outperforms classic panels on several points. Light efficiency reaches 2.9 µmol/J compared to 2.3 µmol/J for a Mars Hydro TS. The modular distribution eliminates shaded areas and ensures homogeneous coverage – whereas a fixed panel creates hot spots in the center. Adjustable UV/IR spectra allow optimization of each phase, which is impossible with a fixed spectrum. The only drawback: a higher initial investment, compensated by a longer lifespan and energy savings.
How do I install the interchangeable LED bars of the Spider Series in my Homebox?
Installation is done with the supplied rails that attach to the horizontal bars of the Homebox. Space the bars 20-25cm apart for optimal coverage. First, connect all bars in series with the DC cables, then plug the main driver into the mains. Use the adjustable hanging straps to maintain 30-40cm between the bars and the canopy. The control cable plugs into the external dimmer – place it outside the tent to avoid humidity.
How often should I clean the LED bars of the Spider Series to maintain optimal PPFD?
Clean the bars every 2-3 weeks with a slightly damp microfiber cloth. Dust and residue reduce light efficiency by 10-15% in a few months. Always turn off the light and wait 30 minutes for cooling before cleaning. Avoid chemicals that could damage the diode coating. Regular maintenance maintains the initial PPFD and extends the lifespan of Samsung LEDs beyond 50,000 hours.
